#SMARTTHINGS HONEYWELL TCC SMARTAPP INSTALL#
#SMARTTHINGS HONEYWELL TCC SMARTAPP DRIVER#
#SMARTTHINGS HONEYWELL TCC SMARTAPP PRO#
#SMARTTHINGS HONEYWELL TCC SMARTAPP OFFLINE#

SmartApps are custom applications that execute outside of the SmartThings Platform.

Developing Your SmartThings Find Device.

Get Started With Mobile Connected Devices.

#SMARTTHINGS HONEYWELL TCC SMARTAPP DRIVER#

LAN Edge Device Driver Development Guide.

#SMARTTHINGS HONEYWELL TCC SMARTAPP INSTALL#

Enroll in a Shared Channel and Install Drivers.Get Started with Cloud Connected Devices.Get Started with Direct Connected Devices.Device Configurations and Presentations.Automations based on motion/window contact sensors are much more reliable. When I press to play a scene in ST to turn all thermostats off, switch them all to fan only, or switch them back to Auto automations fire every single time. I switched all 4 to ecobee 2 weeks ago and the user experience has been much better.

If I wanted just straight scheduling, I could get that in the native app. Automations based on motion sensors/window contact sensors proved to be just too much to accurately keep the thermostats in the correct modes at least 75% of the time. It will fail all or parts of the automation every time. You can forget any kind of frequent automation in ST.

#SMARTTHINGS HONEYWELL TCC SMARTAPP OFFLINE#

Thermostats in the new ST app don’t refresh regularly, so they constantly appear offline until you refresh them.īecause of the above mentioned issue, you can’t run scenes for Thermostats in ST without manually “waking the thermostat” first which defeats the purpose of having a 1 click scene if you have to wake the thermostats up before it will successfully communicate the routine. They always respond and press a button to refresh my signal or whatever but it was a constant issue and if the device isn’t connected, no automations can run. I’ve tweeted them at least 30 times in a year. Native app losing thermostats constantly (and no it’s not my ubiquiti commercial grade wireless internet). I just ripped out all 4 of my Honeywell Lyrics after a year of poor user experience. It’s disabled by default but you can use a enhanced thermostat device handler which support this model to enable Auto change over and then it should automatically switch between heating and cooling based on the setpoints: Enhanced Z-Wave Thermostat Device Handler with Z-Wave Plus

This makes the thermostat switch between Heat and Cool modes automatically so you don’t need to do it manually or through an app. The Honeywell T6 thermostat supports Auto Changeover. The auto mode is the auto changeover option. Some SmartApps are specifically designed to have a closed loop and verify that commands aren’t lost the in the mesh, such as Mode Based Thermostat - Control Multiple Thermostats Temperature / Remote Temperature Sensors when Changing Modes and 5-2 Day Programmable Thermostat Scheduler (Weekday, Weekend) with Remote Temperature Sensor for each Schedule If the mesh is weak it can lose packets and if the SmartApp isn’t aware that it’s losing packets then assume that the command succeeded and wont’ sent it again. The mesh is the Z-Wave mesh that the thermostat uses to communicate with the hub. But now, ST just doesn’t seem to be giving the order to switch over. It did switch back to AC the next day when it got over 74. It got to 65 out and kicked on the heat, and I found that I didn’t need the heater on quite yet, and 74 would be just fine, so I adjusted it.

But, what’s odd is I had originally set it up to kick on the heat at 65 outside, and had set it to be 76 inside. Sure enough, it was 72 inside, and the thermostat was still on AC. The other night it got down into the 50’s, and I noticed the house seemed a bit cool. The house is able to keep it warm enough in that gap, and I can open the windows. I like the keep the house at 74, and I set up two automations in ST, one that when the outside temp is 74 or above, it turns on the AC, and one that when it gets down to 60 outside, it turns on the heat. I can manually control it with ST, but the automations don’t seem to be working, though it has before. But I’m finding out that ST is not actually doing anything now.

#SMARTTHINGS HONEYWELL TCC SMARTAPP PRO#

I have a Honeywell Lyric T6 Pro that I added to my SmartThings hub.

Smartthings honeywell tcc smartapp